Related matching accessories
we have English/Russia/Chinese version APK ,and other install files, and connect documents
if you need it , provide your e-mail , and we will send you
and we also have English connect video,contact us for it 🙂
We also have other current version , you can search in our store 🙂
300A Current + MOS Tube + Display Screen
Russia language video ://www.youtube.com/watch?time_continue=1&v=9caa03JSWhM
BMS battery pack protection board function description:
1. Protection board support 8-24 cells any battery pack (lithium titanate, iron lithium, ternary, Li-ion , Lipo,lifepo4 etc.) (greater than 18v)
2. Battery voltage detection, voltage detection range 1-5v (less than 1v and higher than 5v can not be detected), high precision, integrated error of less than 5mv, applicable to all the voltage within the scope of the battery pack used, overshoot Protection, over discharge protection voltage can be set within this range.
3. With a controlled equalization method, the charge can be balanced by detecting that the differential pressure is greater than the set value.
3. Current measurement (support within 300a current measurement)
4. High-precision coulometer function, based on the current on the time integral, accurate calculation of the remaining battery capacity, charge and so on.
5. Support Android phone set different battery parameters, see the single voltage and current information
6. Support the screen shows the battery status, parameters, each unit voltage
7. Based on the motor Hall pulse detection speed, and can calculate the remaining mileage
8. Independent 6-way temperature measurement, you can set the temperature over-temperature protection value
9. Dual independent watchdog real-time monitoring program plus two protection, never crash!
10. Screen power supply 24V-100V 11.Protection board size: Length 15.5CM Width 7CM Thickness 2.5CM
Need more document , contact us ~
temperature sensor connect :
include the screen+ protection board + wires and other kits
About starting and closing buttons:
1. If the protection board is turned off due to abnormal power failure, only a short press button is needed to start the normal operation of the BMS.
2. During the normal operation of the protection board, press and hold this button for more than 5 seconds, then release the button, the protection board will automatically turn off the power, stop working, zero power consumption, short press can realize the display of the matching screen of the switching protection board.
3. Protection board If the discharge tube is not turned on for more than 5 minutes, the protection board will automatically turn off the main power, stop working, and consume zero power.
4. If the BMS power supply is turned off for the reasons of the second and third conditions, press the power button for 3 seconds to start the normal operation of the protection board.
5. If a matching display is connected, short press this button to switch the screen display.
6. Power button Please ensure good insulation, otherwise it may not be able to automatically turn off the BMS power supply.
About onboard Bluetooth;
Bluetooth is turned on only when the mainboard is not in standby status. After 3 minutes the board is power on, board no current will enter standby status and Bluetooth will be turned off. Having the discharge or charging current , the system will cancel the standby status and Bluetooth will be turned on. You can observe the power led lights on both sides of the protection board. If they are always on, you can connect Bluetooth. If the system is standby, you can short press the protection board start button to activate Bluetooth once. Or re-start the protection board to activate Bluetooth. Make sure Bluetooth is turned on. In the phone’s system settings Bluetooth settings, search for Bluetooth devices. Search once without searching. Please search multiple times. The name (BMS_ANT) sometimes shows null, click the pairing password 1234. Open the APP you download and click Connect the device, select the device you just paired to connect
Protection board calibration:
1. Single cell voltage calibration: You can adjust the “system reference voltage” (the default is about 3.0) to slowly increase the size of 0.001, turn down, you can change the unit voltage value until accurate!
2. Total pressure calibration: You can adjust the “total pressure calibration parameter” (the default is about 3330), slowly adjust the size of this value, you can change the total pressure until accurate!
3. Current calibration: You can adjust the “current sensor range”, slowly adjust the size of this value, you can change the current until accurate!
Note: Do not change the “Power Start Current” # in the parameter setting. If it is too large, it may result in burning and discharging the MOS transistor! ! !
About the automatic balance function:
The auto-balance function is mainly a function that sets the battery’s difference too much. Users must use it when the battery is fully charged or nearly fully charged. When the battery is fully charged, unplug the charger and click ” Auto balance, at this time, the protection board will automatically balance until the battery pack voltagge difference is less than 0.001, or the user clicks on “automatic balance” again to turn off, whether the automatic balance is turned on or off can switch the screen to “system state” to view “balance “Status. If “Auto balance ” is displayed, it means that the automatic balance is in progress!